# Gambrel shed: 8 × 8 gambrel shed [View illustrated instructions](https://diyplans.org/plans/gambrel-shed/8x8) A 64-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. ## License Copyright 2026 DIYplans.org. All rights reserved. ## Configurations - [10x12 ft](https://diyplans.org/plans/gambrel-shed.md): A 120-square-foot shed with evenly spaced continuous skids, a five-sheet T&G floor, a wall-supported rear loft, paired gambrel end frames, layered roofing, T1-11 plywood siding throughout and exterior-framed double doors. Revision 6. Default configuration. - [8 × 8 gambrel shed](https://diyplans.org/plans/gambrel-shed/8x8.md): A 64-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [8 × 10 gambrel shed](https://diyplans.org/plans/gambrel-shed/8x10.md): An 80-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [8 × 12 gambrel shed](https://diyplans.org/plans/gambrel-shed/8x12.md): A 96-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [10 × 10 gambrel shed](https://diyplans.org/plans/gambrel-shed/10x10.md): A 100-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [10 × 16 gambrel shed](https://diyplans.org/plans/gambrel-shed/10x16.md): A 160-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [12 × 12 gambrel shed](https://diyplans.org/plans/gambrel-shed/12x12.md): A 144-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [12 × 16 gambrel shed](https://diyplans.org/plans/gambrel-shed/12x16.md): A 192-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [12 × 20 gambrel shed](https://diyplans.org/plans/gambrel-shed/12x20.md): A 240-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. - [12 × 24 gambrel shed](https://diyplans.org/plans/gambrel-shed/12x24.md): A 288-square-foot gambrel shed with a T&G main floor, wall-supported storage loft, paired end framing, T1-11 exterior and framed double doors. Revision 5. Revision: 5 Status: published Difficulty: advanced ## Before you start - Unverified concept materials. Not construction-ready. Obtain independent qualified design and review before building. - Use the loft for light storage and occasional access only, not living space. Have a qualified professional confirm the two-ply 2x8 beam for this shed width, lumber species and grade, and check its fasteners, hangers, bearing, ledger, floor supports and foundation before building. - The truss plates, door hardware and roof metal show placement only. Choose the actual products before construction. Use an engineered truss connection design and follow the selected products' fastening and weatherproofing instructions. - Tongue-and-groove flooring and T1-11 siding vary by manufacturer. Check the usable panel size, tongue and groove orientation, structural rating and installation instructions before cutting. - Use the plans, drawings and cut lists for your chosen shed size together. - Use nominal stock names for purchasing and actual dressed dimensions for layout. - Check delivered stock lengths before cutting; full-length pieces have no end-trimming reserve. - Follow the selected product instructions for panel gaps, factory profiles, fasteners, flashing and roof laps. - Plan wall and roof lifts, temporary bracing, work platforms and fall protection before assembly. ## Dimensions - Floor width: 96 in - Floor depth: 96 in - Floor area: 64 ft² - Wall height: 84 in - Clear door width: 64 in - Clear door height: 72 in - Loft deck height: 80 3/4 in - Loft depth: 48 in ## Shopping list [Get the plan package for $19 USD](https://diyplans.org/buy/gambrel-shed). Includes available shopping lists, cut lists and downloads for every configuration of this plan. ## Tools and equipment - Tape measure, framing square, pencil and chalk line - Level, string line and laser or water level - Circular saw and supported sheet-cutting surface - Miter saw or clamped repeat-cut guide - Jigsaw for shaped cuts - Drill-driver and the selected fastener bits - Hammer or nailer matched to specified nails - Clamps, sawhorses and flat assembly platform - Roofing knife and metal snips - Caulk gun, brushes and rollers - Stable ladders and work platforms - Eye, hearing and dust protection; work gloves ## Instructions ### 1. Confirm the construction details - Use the 8x8 plans and cut lists together. Mark the 96 by 96-inch footprint and the 64 by 72-inch door opening on the project drawings. - Obtain the site foundation, anchorage, bracing and framing connection details before ordering affected materials. - Resolve loft beam and ledger connections, roof-joint connectors and roof-spread restraint. Keep the loft for light storage with occasional access only after its permitted load and access details are established. - Select the actual T&G floor, T1-11 siding, roofing and door hardware; use their product instructions for gaps, laps, clearances and fastening. Check: The required site details, product instructions and fastening schedules are available. Reference drawings: - [Footprint skids](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-footprint-skids/footprint-skids.svg?brand=1) - [Front elevation](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-elevation/front-elevation.svg?brand=1) ### 2. Lay out the footprint - Mark a 96 by 96-inch rectangle for the outside floor edges. Label the door end front. - Set the front-left floor corner as the datum. Measure X across the door wall, Y toward the rear and Z upward from the finished main floor. - Compare the two diagonals and adjust until they match. - Mark runner centerlines at X = 5 1/4, 48, 90 3/4 inches. Use the foundation drawing for support pads and any supported joints. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Footprint skids](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-footprint-skids/footprint-skids.svg?brand=1) Footprint skids ### 3. Prepare the foundation - Prepare drainage and bearing pads using the approved site detail. Remove unsuitable bearing material as that detail requires. - Level the support points along and across every runner line. Install the specified anchors while they are accessible. - Place a support under every runner end or splice shown in the drawing. Keep the required wood-to-ground clearance. Check: All runner bearing points are level, stable and located for the actual joints. Reference drawings: - [Footprint skids](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-footprint-skids/footprint-skids.svg?brand=1) ### 4. Set the foundation runners - 2 treated foundation runner: 4x4 treated, 96 in long, actual section 3 1/2 x 3 1/2 in. - 1 treated foundation runner: 4x4 treated, 96 in long, actual section 3 1/2 x 3 1/2 in. - Place the runners front to rear on centerlines X = 5 1/4, 48, 90 3/4 inches. - Keep each scheduled full-length piece continuous. Where the drawing divides a runner, center its joint over the specified foundation support. - Complete the foundation anchorage detail and recheck level. Check: Each runner is continuously supported at the specified bearing points and anchored. ![Set the foundation runners. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-006/s04.gif?brand=1) Movement study for Set the foundation runners. Reference drawings: - [Footprint skids](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-footprint-skids/footprint-skids.svg?brand=1) ### 5. Cut and mark the floor stock - 1 treated side floor rim: 2x6 treated, 96 in long, actual section 1 1/2 x 5 1/2 in. - 1 treated side floor rim: 2x6 treated, 96 in long, actual section 1 1/2 x 5 1/2 in. - 1 treated floor joist: 2x6 treated, 93 in long, actual section 1 1/2 x 5 1/2 in. - 4 treated floor joist: 2x6 treated, 93 in long, actual section 1 1/2 x 5 1/2 in. - 1 treated floor joist: 2x6 treated, 93 in long, actual section 1 1/2 x 5 1/2 in. - 1 treated floor joist: 2x6 treated, 93 in long, actual section 1 1/2 x 5 1/2 in. - 4 loft wall bearing block: 2x6 treated, 5 1/2 in long, actual section 1 1/2 x 5 1/2 in. - 4 loft wall bearing block: 2x6 treated, 5 1/2 in long, actual section 1 1/2 x 5 1/2 in. - Mark joist centerlines at Y = 3/4, 16, 32, 48, 64, 80, 95 1/4 inches from the front datum on both bare side rims. - Mark bearing-block locations from the floor drawing. Preserve these loft reaction blocks; do not add the removed seam-only grid. - Keep scheduled continuous pieces whole and treat cut ends according to the preservative supplier. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Floor cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-cut-layout/floor-cut-layout.svg?brand=1) Floor cut layout Reference drawings: - [Floor frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-frame/floor-frame.svg?brand=1) ### 6. Assemble the floor perimeter - Align the side rims along the outside floor edges and fit the front and rear joists between them. - Keep the outside dimensions 96 by 96 inches and bring all top edges into one plane. - Fasten the corners using the framing schedule. Keep any scheduled rim joint over its specified support. Check: The perimeter is rectangular and every scheduled rim joint has its required bearing. ![Assemble the floor perimeter. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-008/s06.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Floor frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-frame/floor-frame.svg?brand=1) ### 7. Install the floor joists - Set the remaining joists on the marked centerlines Y = 16, 32, 48, 64, 80 inches. - Place crowns upward, align top edges with the rims and seat the joists on the runners. - Connect joist ends and runner crossings using the selected framing and anchorage details. Check: Every joist is seated at its runner crossings and flush with the floor perimeter. ![Install the floor joists. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-009/s07.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Floor frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-frame/floor-frame.svg?brand=1) ### 8. Install the loft bearing blocks - 4 loft wall bearing block: 2x6 treated, 5 1/2 in long, actual section 1 1/2 x 5 1/2 in. - 4 loft wall bearing block: 2x6 treated, 5 1/2 in long, actual section 1 1/2 x 5 1/2 in. - Fit the blocks at the wall-supported loft beam reactions shown in the drawing. - Keep block tops flush with the joists and complete their specified attachment before covering the floor. Check: The wall reactions have a continuous path through the retained floor blocking to the outer runner lines. ![Install the loft bearing blocks. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-010/s08.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Floor frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-frame/floor-frame.svg?brand=1) - [Loft bearing](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-bearing/loft-bearing.svg?brand=1) ### 9. Square and anchor the floor - Compare the floor diagonals, correct the rectangle and recheck level. - Complete all floor-to-runner and runner-to-foundation connections before decking conceals them. - Check for gaps at bearing contacts and correct them using the foundation detail. Check: The frame is square, level and connected. Reference drawings: - [Floor frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-frame/floor-frame.svg?brand=1) ### 10. Plan the T&G floor panels - Prepare the 3 floor panels using the exact sheet allocation and factory-edge schedule. - Check the selected product against the modeled 23/32-inch thickness and required usable face width. - Run the panel strength direction front to rear, perpendicular to the floor joists. Retain each specified factory tongue and groove. - Mark short-end cuts from the supported joint positions. Do not substitute square edges at unsupported long joints. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Floor sheet layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-sheet-layout/floor-sheet-layout.svg?brand=1) Floor sheet layout Reference drawings: - [Floor panel layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-panel-layout/floor-panel-layout.svg?brand=1) ### 11. Lay floor strip 1 - Start this strip at X = 0 inches from the left floor datum. - 1 t&g floor panel: 23/32 T&G plywood, full face, 95 7/8 in long, actual section 23/32 x 48 in. - Set the panels in the positions shown; engage the retained factory profiles without forcing them. - Maintain the selected product gaps, support the short-end joints on joists and fasten using its panel schedule. Check: The strip lies flat; its specified factory edges and short-end supports remain intact. ![Lay floor strip 1. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-013/s11.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Floor panel layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-panel-layout/floor-panel-layout.svg?brand=1) ### 12. Lay floor strip 2 - Start this strip at X = 48 1/8 inches from the left floor datum. - 2 t&g floor panel: 23/32 T&G plywood, full face, 47 7/8 in long, actual section 23/32 x 47 7/8 in. - Set the panels in the positions shown; engage the retained factory profiles without forcing them. - Maintain the selected product gaps, support the short-end joints on joists and fasten using its panel schedule. Check: The strip lies flat; its specified factory edges and short-end supports remain intact. ![Lay floor strip 2. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-014/s12.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Floor panel layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-panel-layout/floor-panel-layout.svg?brand=1) ### 13. Cut and mark the left wall - 1 left wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 left wall corner backing stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 4 left wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 left wall corner backing stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 left wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 left wall bottom plate: 2x4, 96 in long, actual section 1 1/2 x 3 1/2 in. - 1 left wall first top plate: 2x4, 96 in long, actual section 1 1/2 x 3 1/2 in. - 1 loft beam wall jack: 2x4, 71 1/4 in long, actual section 1 1/2 x 3 1/2 in. - 1 loft beam wall jack: 2x4, 71 1/4 in long, actual section 1 1/2 x 3 1/2 in. - 1 loft beam wall king: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - Use the matching cut list for the remaining distinct sizes. - Lay the matching first-layer plates side by side and transfer the member stations from the wall drawing. - Mark both stud edges and label opening, corner-backing and loft-seat members before fastening. - Keep second top plates aside until all four walls are standing. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Left wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-left-wall-cut-layout/left-wall-cut-layout.svg?brand=1) Left wall cut layout ![Left wall cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-left-wall-cut-layout-02/left-wall-cut-layout-02.svg?brand=1) Left wall cut layout 02 Reference drawings: - [Left wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-left-wall-frame/left-wall-frame.svg?brand=1) ### 14. Assemble and raise the left wall - Assemble the labeled plates and studs flat on a supported work surface; align the reference edges and square the frame. - Fit the corner backing and any wall-contained loft king and jack studs at their drawing positions. Keep the beam pockets open above the jacks. - Fasten using the wall connection schedule, then use the planned lifting method and enough helpers to raise the wall. - Plumb, anchor and temporarily brace the wall before releasing it. Check: The left wall is plumb, anchored and braced; its opening and support pockets match the drawing. ![Assemble and raise the left wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-017/s14.gif?brand=1) Movement study for Assemble and raise the left wall. Reference drawings: - [Left wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-left-wall-frame/left-wall-frame.svg?brand=1) ### 15. Cut and mark the right wall - 1 right wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 right wall corner backing stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 4 right wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 right wall corner backing stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 right wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 right wall bottom plate: 2x4, 96 in long, actual section 1 1/2 x 3 1/2 in. - 1 right wall first top plate: 2x4, 96 in long, actual section 1 1/2 x 3 1/2 in. - 1 loft beam wall jack: 2x4, 71 1/4 in long, actual section 1 1/2 x 3 1/2 in. - 1 loft beam wall jack: 2x4, 71 1/4 in long, actual section 1 1/2 x 3 1/2 in. - 1 loft beam wall king: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - Use the matching cut list for the remaining distinct sizes. - Lay the matching first-layer plates side by side and transfer the member stations from the wall drawing. - Mark both stud edges and label opening, corner-backing and loft-seat members before fastening. - Keep second top plates aside until all four walls are standing. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Right wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-right-wall-cut-layout/right-wall-cut-layout.svg?brand=1) Right wall cut layout ![Right wall cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-right-wall-cut-layout-02/right-wall-cut-layout-02.svg?brand=1) Right wall cut layout 02 Reference drawings: - [Right wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-right-wall-frame/right-wall-frame.svg?brand=1) ### 16. Assemble and raise the right wall - Assemble the labeled plates and studs flat on a supported work surface; align the reference edges and square the frame. - Fit the corner backing and any wall-contained loft king and jack studs at their drawing positions. Keep the beam pockets open above the jacks. - Fasten using the wall connection schedule, then use the planned lifting method and enough helpers to raise the wall. - Plumb, anchor and temporarily brace the wall before releasing it. Check: The right wall is plumb, anchored and braced; its opening and support pockets match the drawing. ![Assemble and raise the right wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-020/s16.gif?brand=1) Movement study for Assemble and raise the right wall. Reference drawings: - [Right wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-right-wall-frame/right-wall-frame.svg?brand=1) ### 17. Cut and mark the rear wall - 1 rear wall bottom plate: 2x4, 89 in long, actual section 1 1/2 x 3 1/2 in. - 1 rear wall first top plate: 2x4, 89 in long, actual section 1 1/2 x 3 1/2 in. - 5 rear wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 rear wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 rear wall stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - Lay the matching first-layer plates side by side and transfer the member stations from the wall drawing. - Mark both stud edges and label opening, corner-backing and loft-seat members before fastening. - Keep second top plates aside until all four walls are standing. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Rear wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-rear-wall-cut-layout/rear-wall-cut-layout.svg?brand=1) Rear wall cut layout Reference drawings: - [Rear wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-rear-wall-frame/rear-wall-frame.svg?brand=1) ### 18. Assemble and raise the rear wall - Assemble the labeled plates and studs flat on a supported work surface; align the reference edges and square the frame. - Fit the corner backing and any wall-contained loft king and jack studs at their drawing positions. Keep the beam pockets open above the jacks. - Fasten using the wall connection schedule, then use the planned lifting method and enough helpers to raise the wall. - Plumb, anchor and temporarily brace the wall before releasing it. Check: The rear wall is plumb, anchored and braced; its opening and support pockets match the drawing. ![Assemble and raise the rear wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-023/s18.gif?brand=1) Movement study for Assemble and raise the rear wall. Reference drawings: - [Rear wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-rear-wall-frame/rear-wall-frame.svg?brand=1) ### 19. Cut and mark the front wall - 2 front wall bottom plate: 2x4, 12 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 front wall first top plate: 2x4, 89 in long, actual section 1 1/2 x 3 1/2 in. - 2 front wall king or full stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 front wall king or full stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 front wall king or full stud: 2x4, 79 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 door header jack stud: 2x4, 70 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 door header jack stud: 2x4, 70 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 1 door header ply: 2x6, 67 in long, actual section 1 1/2 x 5 1/2 in. - 1 door header ply: 2x6, 67 in long, actual section 1 1/2 x 5 1/2 in. - 1 door header spacer: 1/2 plywood, 67 in long, actual section 1/2 x 5 1/2 in. - Use the matching cut list for the remaining distinct sizes. - Lay the matching first-layer plates side by side and transfer the member stations from the wall drawing. - Mark both stud edges and label opening, corner-backing and loft-seat members before fastening. - Keep second top plates aside until all four walls are standing. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Front wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-wall-cut-layout/front-wall-cut-layout.svg?brand=1) Front wall cut layout ![Front wall cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-wall-cut-layout-02/front-wall-cut-layout-02.svg?brand=1) Front wall cut layout 02 Reference drawings: - [Front wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-wall-frame/front-wall-frame.svg?brand=1) ### 20. Assemble and raise the front wall - Frame the 64 by 72-inch clear opening with the labeled king studs, jacks, header plies, spacer and cripples. - Measure the opening height from the finished floor datum. Keep the header underside at the drawing elevation. - Assemble and square the front wall on a supported platform; fasten according to the selected header and wall connection details. - Lift the wall into place, align it between the side walls and plumb, anchor and brace it. Check: The front wall is plumb, anchored and braced; its opening and support pockets match the drawing. ![Assemble and raise the front wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-026/s20.gif?brand=1) Movement study for Assemble and raise the front wall. Reference drawings: - [Front wall frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-wall-frame/front-wall-frame.svg?brand=1) ### 21. Lap the wall cap plates - 1 left wall cap plate: 2x4, 89 in long, actual section 1 1/2 x 3 1/2 in. - 1 right wall cap plate: 2x4, 89 in long, actual section 1 1/2 x 3 1/2 in. - 1 rear wall cap plate: 2x4, 96 in long, actual section 1 1/2 x 3 1/2 in. - 1 front wall cap plate: 2x4, 96 in long, actual section 1 1/2 x 3 1/2 in. - Fit the second top plates over the standing walls using the marked corner laps and staggered joint positions. - Bring the completed cap surface to Z = 84 inches above the floor. - Complete the specified wall-to-wall ties and recheck the wall diagonals, plumb and temporary bracing. Check: Caps tie the walls together with the drawn corner laps and joint offsets. ![Lap the wall cap plates. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-027/s21.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Wall caps](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-wall-caps/wall-caps.svg?brand=1) ### 22. Cut and mark the loft framing - 1 flush loft beam ply: 2x8, 96 in long, actual section 1 1/2 x 7 1/4 in. - 1 flush loft beam ply: 2x8, 96 in long, actual section 1 1/2 x 7 1/4 in. - 1 loft rear ledger: 2x6, 89 in long, actual section 1 1/2 x 5 1/2 in. - 5 loft joist: 2x6, 44 7/8 in long, actual section 1 1/2 x 5 1/2 in. - 1 loft joist: 2x6, 44 7/8 in long, actual section 1 1/2 x 5 1/2 in. - 1 loft joist: 2x6, 44 7/8 in long, actual section 1 1/2 x 5 1/2 in. - Mark the beam-end bearing, rear ledger and joist stations from the loft drawing. - Select the joist hangers, beam-ply fastening and ledger anchors before cutting connection-dependent details. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Loft cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-cut-layout/loft-cut-layout.svg?brand=1) Loft cut layout Reference drawings: - [Loft layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-layout/loft-layout.svg?brand=1) - [Loft bearing](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-bearing/loft-bearing.svg?brand=1) ### 23. Seat the wall-supported loft beam - Assemble the continuous beam plies using the selected ply-fastening detail. - Lower the beam onto the paired wall seats with the planned lifting method; keep both ends fully seated. - Complete beam-end and wall-support connections. Keep the main floor free of interior posts. Check: Both beam ends bear at the drawn wall seats and are restrained by the selected connections. ![Seat the wall-supported loft beam. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-030/s23.gif?brand=1) Movement study for Seat the wall-supported loft beam. Reference drawings: - [Loft bearing](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-bearing/loft-bearing.svg?brand=1) - [Loft layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-layout/loft-layout.svg?brand=1) ### 24. Attach the rear loft ledger - 1 loft rear ledger: 2x6, 89 in long, actual section 1 1/2 x 5 1/2 in. - Set the ledger at its drawing height against the rear-wall studs. - Install the selected structural anchors into the required backing; verify edge distances and bearing. Check: The ledger is level and attached using its specified structural connection. ![Attach the rear loft ledger. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-031/s24.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Loft layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-layout/loft-layout.svg?brand=1) ### 25. Install the loft joists - Mark joist centerlines at X = 4 1/4, 16, 32, 48, 64, 80, 91 3/4 inches. - 5 loft joist: 2x6, 44 7/8 in long, actual section 1 1/2 x 5 1/2 in. - 1 loft joist: 2x6, 44 7/8 in long, actual section 1 1/2 x 5 1/2 in. - 1 loft joist: 2x6, 44 7/8 in long, actual section 1 1/2 x 5 1/2 in. - Fit each front end in its selected hanger and retain the drawn rear bearing on the ledger. - Use the connector manufacturer’s fasteners; do not substitute general-purpose screws. Check: Every loft joist has the specified front connector and rear bearing. ![Install the loft joists. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-032/s25.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Loft layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-layout/loft-layout.svg?brand=1) ### 26. Cut the loft panels - 1 loft deck panel: 3/4 plywood, 89 in long, actual section 3/4 x 48 in. - Mark the supported panel joints from the loft drawing and follow the sheet allocation. - Keep the specified strength direction and panel gaps. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Loft deck layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-deck-layout/loft-deck-layout.svg?brand=1) Loft deck layout ### 27. Fasten the loft deck - Fit the loft panels with their short joints supported as drawn. - Fasten using the selected panel schedule and inspect the edge support. - Keep the loft unloaded until its permitted load, access and edge-protection details are complete. Check: The deck is supported and fastened, with unresolved access and loading requirements recorded. ![Fasten the loft deck. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-034/s27.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. Reference drawings: - [Loft deck layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-deck-layout/loft-deck-layout.svg?brand=1) ### 28. Cut and label the roof profiles - 5 left lower rafter: 2x4, 31 7/8 in long, actual section 1 1/2 x 3 1/2 in. - 5 left upper rafter: 2x4, 36 1/2 in long, actual section 1 1/2 x 3 1/2 in. - 5 right lower rafter: 2x4, 31 7/8 in long, actual section 1 1/2 x 3 1/2 in. - 5 right upper rafter: 2x4, 36 1/2 in long, actual section 1 1/2 x 3 1/2 in. - Transfer the exact stock-coordinate profiles to the marked blanks; keep mirrored parts labeled. - Cut one complete gambrel frame first and dry-fit it against the roof layout before repeating the cuts. - Use an engineered roof-joint connection design. The plates shown indicate their positions, not a product specification. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Rafter cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-rafter-cut-layout/rafter-cut-layout.svg?brand=1) Rafter cut layout Reference drawings: - [Gambrel profile](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gambrel-profile/gambrel-profile.svg?brand=1) ### 29. Raise the front end roof frame - Assemble the four labeled members on a flat layout using the specified roof connectors and fastening process. - Lift the completed frame onto the caps at centerline Y = 3/4 inches. Preserve its left/right orientation. - Hold the frame plumb and complete the designed bearing, uplift and spread-restraint connections. - Brace the frame before releasing the lifting support and keep prior frames restrained. Check: The frame is seated, plumb, connected and temporarily braced. ![Raise the front end roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-037/s29.gif?brand=1) Movement study for Raise the front end roof frame. Reference drawings: - [Gambrel profile](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gambrel-profile/gambrel-profile.svg?brand=1) - [Roof stations](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-stations/roof-stations.svg?brand=1) ### 30. Raise the rear end roof frame - Assemble the four labeled members on a flat layout using the specified roof connectors and fastening process. - Lift the completed frame onto the caps at centerline Y = 95 1/4 inches. Preserve its left/right orientation. - Hold the frame plumb and complete the designed bearing, uplift and spread-restraint connections. - Brace the frame before releasing the lifting support and keep prior frames restrained. Check: The frame is seated, plumb, connected and temporarily braced. ![Raise the rear end roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-039/s30.gif?brand=1) Movement study for Raise the rear end roof frame. Reference drawings: - [Gambrel profile](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gambrel-profile/gambrel-profile.svg?brand=1) - [Roof stations](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-stations/roof-stations.svg?brand=1) ### 31. Raise the intermediate 1 roof frame - Assemble the four labeled members on a flat layout using the specified roof connectors and fastening process. - Lift the completed frame onto the caps at centerline Y = 24 inches. Preserve its left/right orientation. - Hold the frame plumb and complete the designed bearing, uplift and spread-restraint connections. - Brace the frame before releasing the lifting support and keep prior frames restrained. Check: The frame is seated, plumb, connected and temporarily braced. ![Raise the intermediate 1 roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-041/s31.gif?brand=1) Movement study for Raise the intermediate 1 roof frame. Reference drawings: - [Gambrel profile](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gambrel-profile/gambrel-profile.svg?brand=1) - [Roof stations](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-stations/roof-stations.svg?brand=1) ### 32. Raise the intermediate 2 roof frame - Assemble the four labeled members on a flat layout using the specified roof connectors and fastening process. - Lift the completed frame onto the caps at centerline Y = 48 inches. Preserve its left/right orientation. - Hold the frame plumb and complete the designed bearing, uplift and spread-restraint connections. - Brace the frame before releasing the lifting support and keep prior frames restrained. Check: The frame is seated, plumb, connected and temporarily braced. ![Raise the intermediate 2 roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-043/s32.gif?brand=1) Movement study for Raise the intermediate 2 roof frame. Reference drawings: - [Gambrel profile](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gambrel-profile/gambrel-profile.svg?brand=1) - [Roof stations](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-stations/roof-stations.svg?brand=1) ### 33. Raise the intermediate 3 roof frame - Assemble the four labeled members on a flat layout using the specified roof connectors and fastening process. - Lift the completed frame onto the caps at centerline Y = 72 inches. Preserve its left/right orientation. - Hold the frame plumb and complete the designed bearing, uplift and spread-restraint connections. - Brace the frame before releasing the lifting support and keep prior frames restrained. Check: The frame is seated, plumb, connected and temporarily braced. ![Raise the intermediate 3 roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-045/s33.gif?brand=1) Movement study for Raise the intermediate 3 roof frame. Reference drawings: - [Gambrel profile](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gambrel-profile/gambrel-profile.svg?brand=1) - [Roof stations](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-stations/roof-stations.svg?brand=1) ### 34. Cut the gable infill and spacers - Transfer the exact gable-stud and relieved-spacer profiles from the cut-profile drawings. - Keep the gable studs perpendicular to the end wall, with their full wall depth front to rear. - Label front and rear spacers and inner rafters; keep their connector reliefs correctly oriented. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Gable cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout/gable-cut-layout.svg?brand=1) Gable cut layout ![Gable cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-02/gable-cut-layout-02.svg?brand=1) Gable cut layout 02 ![Gable cut layout 03](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-03/gable-cut-layout-03.svg?brand=1) Gable cut layout 03 ![Gable cut layout 04](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-04/gable-cut-layout-04.svg?brand=1) Gable cut layout 04 ![Gable cut layout 05](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-05/gable-cut-layout-05.svg?brand=1) Gable cut layout 05 Reference drawings: - [Paired end frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-paired-end-frame/paired-end-frame.svg?brand=1) ### 35. Fit the perpendicular gable infill - Fit the 10 shaped infill members at the front and rear positions shown. - Seat their lower ends on the wall caps and fit the angled tops to the drawn roof boundary. - Keep their full wall depth perpendicular to the end face and fasten with the selected end-wall detail. Check: The infill follows the roof outline and preserves the full end-wall depth. ![Fit the perpendicular gable infill. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-047/s35.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Gable framing](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-framing/gable-framing.svg?brand=1) ### 36. Fit the relieved end-frame spacers - Place the shaped plywood spacers against the inside of the outer end rafters. - Align each relief with the connector location and preserve the specified cavity. - Fasten with the selected paired-frame detail; do not fill connector clearances with unshown packing. Check: Every spacer is oriented correctly and the connector reliefs remain open. ![Fit the relieved end-frame spacers. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-048/s36.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Paired end frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-paired-end-frame/paired-end-frame.svg?brand=1) ### 37. Fit the inner end rafters - Fit the additional inner rafters against the spacer faces, matching each labeled profile. - Keep the inner faces aligned with the end-wall lining plane. - Complete the selected frame-to-spacer connection. Choose insulation, lining and moisture control separately. Check: The paired end assemblies finish flush to their intended inner lining plane. ![Fit the inner end rafters. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-050/s37.gif?brand=1) Movement study for Fit the inner end rafters. Reference drawings: - [Paired end frame](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-paired-end-frame/paired-end-frame.svg?brand=1) ### 38. Lay out the T1-11 siding cuts - Verify the delivered panel-body thickness and usable factory-lap coverage before cutting. - Keep all grooves vertical. Cut square wall blanks from the sheet allocation and transfer shaped gable and door-opening profiles exactly. - Seal cut edges as the panel manufacturer requires. Keep openings, laps and the wall-to-gable joint labeled. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Siding cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-siding-cut-layout/siding-cut-layout.svg?brand=1) Siding cut layout ![Siding cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-siding-cut-layout-02/siding-cut-layout-02.svg?brand=1) Siding cut layout 02 Reference drawings: - [Front siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-siding/front-siding.svg?brand=1) - [Gable siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-siding/gable-siding.svg?brand=1) ### 39. Prepare the wall weather details - Install the selected weather barrier and opening flashings in their required lap order. - Mark fastening lines over the framing and preserve the specified drainage paths. - Prepare the horizontal wall-to-gable seam flashing before trim conceals the joint. Check: The selected wall assembly can drain outward around openings and horizontal joints. Reference drawings: - [Front siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-siding/front-siding.svg?brand=1) ### 40. Fasten the left wall siding - Start from the drawing datum and align the marked factory edges and opening cuts. - Maintain the selected product edge clearances, panel gaps and vertical groove direction. - Fasten into the marked framing with the selected panel schedule; keep drainage and flashing laps open. Check: Panel joints have their required backing and clearances; opening cuts match the frame. ![Fasten the left wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-053/s40.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the left wall. Reference drawings: - [Left siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-left-siding/left-siding.svg?brand=1) ### 41. Fasten the right wall siding - Start from the drawing datum and align the marked factory edges and opening cuts. - Maintain the selected product edge clearances, panel gaps and vertical groove direction. - Fasten into the marked framing with the selected panel schedule; keep drainage and flashing laps open. Check: Panel joints have their required backing and clearances; opening cuts match the frame. ![Fasten the right wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-054/s41.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the right wall. Reference drawings: - [Right siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-right-siding/right-siding.svg?brand=1) ### 42. Fasten the rear wall siding - Start from the drawing datum and align the marked factory edges and opening cuts. - Maintain the selected product edge clearances, panel gaps and vertical groove direction. - Fasten into the marked framing with the selected panel schedule; keep drainage and flashing laps open. Check: Panel joints have their required backing and clearances; opening cuts match the frame. ![Fasten the rear wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-055/s42.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the rear wall. Reference drawings: - [Rear siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-rear-siding/rear-siding.svg?brand=1) ### 43. Fasten the front wall siding - Start from the drawing datum and align the marked factory edges and opening cuts. - Maintain the selected product edge clearances, panel gaps and vertical groove direction. - Fasten into the marked framing with the selected panel schedule; keep drainage and flashing laps open. Check: Panel joints have their required backing and clearances; opening cuts match the frame. ![Fasten the front wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-056/s43.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. Reference drawings: - [Front siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-siding/front-siding.svg?brand=1) ### 44. Fit the gable siding panels - Fit the labeled shaped panels to the front and rear roof outlines. - Keep the wall-to-gable seam at Z = 84 inches and maintain the required joint gaps. - Preserve vertical grooves and complete the selected fastening and seam-flashing detail. Check: Both gables fit their roof outlines and the horizontal seams can drain. ![Fit the gable siding panels. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-057/s44.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Gable siding](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-siding/gable-siding.svg?brand=1) ### 45. Cut and mark the roof panels - 2 roof sheathing panel: 1/2 plywood, 75 15/16 in long, actual section 1/2 x 31 7/8 in. - 2 roof sheathing panel: 1/2 plywood, 27 15/16 in long, actual section 1/2 x 31 7/8 in. - 2 roof sheathing panel: 1/2 plywood, 75 15/16 in long, actual section 1/2 x 36 1/2 in. - 2 roof sheathing panel: 1/2 plywood, 27 15/16 in long, actual section 1/2 x 36 1/2 in. - Use the exact slope-width blanks and sheet allocation. Keep the panel strength direction and supported joints shown. - Mark each lower or upper facet and front-to-rear position before taking panels to the roof. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Roof sheet layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-sheet-layout/roof-sheet-layout.svg?brand=1) Roof sheet layout ![Roof sheet layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-sheet-layout-02/roof-sheet-layout-02.svg?brand=1) Roof sheet layout 02 Reference drawings: - [Roof panel layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-panel-layout/roof-panel-layout.svg?brand=1) ### 46. Fasten the roof sheathing - Place the panels on their labeled roof facets with the specified edge gaps and front/rear overhangs. - Keep panel joints over the framing and complete the selected edge-support and nailing details. - Use stable roof-access equipment and fall protection; keep all roof frames restrained during sheathing. Check: All four roof facets are sheathed with supported joints and aligned overhangs. ![Fasten the roof sheathing. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-059/s46.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof panel layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-panel-layout/roof-panel-layout.svg?brand=1) ### 47. Fit the eave drip edges - Install the selected eave metal before the underlayment, keeping the outer return clear of the siding face. - Follow the product instructions for hidden laps, fastening, exposed coverage and edge terminations. - Use the listed roof areas and lengths to choose product quantities. Add the manufacturer's required overlaps and cutting allowance. - Check each completed transition before concealing it with the next layer. Check: This layer follows the selected roof system and sheds water onto the layer below. ![Fit the eave drip edges. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-060/s47.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof layer detail](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-layer-detail/roof-layer-detail.svg?brand=1) ### 48. Lay the roof underlayment - Lay the selected membrane from lower to upper courses with its required side and end laps. - Follow the product instructions for hidden laps, fastening, exposed coverage and edge terminations. - Use the listed roof areas and lengths to choose product quantities. Add the manufacturer's required overlaps and cutting allowance. - Check each completed transition before concealing it with the next layer. Check: This layer follows the selected roof system and sheds water onto the layer below. ![Lay the roof underlayment. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-061/s48.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof layer detail](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-layer-detail/roof-layer-detail.svg?brand=1) ### 49. Fit the rake drip edges - Fit the rake metal in the lap order required by the selected roof system. - Follow the product instructions for hidden laps, fastening, exposed coverage and edge terminations. - Use the listed roof areas and lengths to choose product quantities. Add the manufacturer's required overlaps and cutting allowance. - Check each completed transition before concealing it with the next layer. Check: This layer follows the selected roof system and sheds water onto the layer below. ![Fit the rake drip edges. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-062/s49.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof layer detail](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-layer-detail/roof-layer-detail.svg?brand=1) ### 50. Shingle the lower roof facets - Install the selected starter and lower field courses, working from eave toward knee. - Follow the product instructions for hidden laps, fastening, exposed coverage and edge terminations. - Use the listed roof areas and lengths to choose product quantities. Add the manufacturer's required overlaps and cutting allowance. - Check each completed transition before concealing it with the next layer. Check: This layer follows the selected roof system and sheds water onto the layer below. ![Shingle the lower roof facets. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-063/s50.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof layer detail](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-layer-detail/roof-layer-detail.svg?brand=1) ### 51. Flash the gambrel knees - Place the transition flashing above the lower shingles, with its upper flange beneath the upper field. - Follow the product instructions for hidden laps, fastening, exposed coverage and edge terminations. - Use the listed roof areas and lengths to choose product quantities. Add the manufacturer's required overlaps and cutting allowance. - Check each completed transition before concealing it with the next layer. Check: This layer follows the selected roof system and sheds water onto the layer below. ![Flash the gambrel knees. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-064/s51.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof layer detail](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-layer-detail/roof-layer-detail.svg?brand=1) ### 52. Shingle the upper roof facets - Work from each knee toward the ridge using the selected exposure and fastening pattern. - Follow the product instructions for hidden laps, fastening, exposed coverage and edge terminations. - Use the listed roof areas and lengths to choose product quantities. Add the manufacturer's required overlaps and cutting allowance. - Check each completed transition before concealing it with the next layer. Check: This layer follows the selected roof system and sheds water onto the layer below. ![Shingle the upper roof facets. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-065/s52.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof layer detail](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-layer-detail/roof-layer-detail.svg?brand=1) ### 53. Finish the ridge - Install the designed ridge closure or ventilation, then lay caps with the selected exposure and laps. - Follow the product instructions for hidden laps, fastening, exposed coverage and edge terminations. - Use the listed roof areas and lengths to choose product quantities. Add the manufacturer's required overlaps and cutting allowance. - Check each completed transition before concealing it with the next layer. Check: This layer follows the selected roof system and sheds water onto the layer below. ![Finish the ridge. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-066/s53.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. Reference drawings: - [Roof layer detail](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-layer-detail/roof-layer-detail.svg?brand=1) ### 54. Cut and lay out the door leaves - Measure the completed opening before cutting the 31 11/16 by 71 5/8-inch leaves. - 1 left t1-11 door skin: 5/8 T1-11 siding panel, 71 5/8 in long, actual section 5/8 x 31 11/16 in. - 1 right t1-11 door skin: 5/8 T1-11 siding panel, 71 5/8 in long, actual section 5/8 x 31 11/16 in. - 2 left exterior door stile: 2x4, 71 5/8 in long, actual section 1 1/2 x 3 1/2 in. - 1 left exterior door bottom rail: 2x4, 24 11/16 in long, actual section 1 1/2 x 3 1/2 in. - 1 left exterior door top rail: 2x4, 24 11/16 in long, actual section 1 1/2 x 3 1/2 in. - 2 right exterior door stile: 2x4, 71 5/8 in long, actual section 1 1/2 x 3 1/2 in. - 1 right exterior door bottom rail: 2x4, 24 11/16 in long, actual section 1 1/2 x 3 1/2 in. - 1 right exterior door top rail: 2x4, 24 11/16 in long, actual section 1 1/2 x 3 1/2 in. - 1 left exterior door middle rail: 2x4, 24 11/16 in long, actual section 1 1/2 x 3 1/2 in. - 1 right exterior door middle rail: 2x4, 24 11/16 in long, actual section 1 1/2 x 3 1/2 in. - Keep the T1-11 grooves vertical and the stiles and rails on the exterior face. - Resolve skin fastening, sag resistance and rated hinge attachments before assembling the leaves. Check: All pieces are marked with their matching cut-list IDs and reference edges. ![Door cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-cut-layout/door-cut-layout.svg?brand=1) Door cut layout ![Door cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-cut-layout-02/door-cut-layout-02.svg?brand=1) Door cut layout 02 Reference drawings: - [Door layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-layout/door-layout.svg?brand=1) ### 55. Fit the door jambs and head - 1 exterior 2x4 door jamb: 2x4, 72 in long, actual section 1 1/2 x 3 1/2 in. - 1 exterior 2x4 door jamb: 2x4, 72 in long, actual section 1 1/2 x 3 1/2 in. - 1 exterior 2x4 door head: 2x4, 71 in long, actual section 1 1/2 x 3 1/2 in. - Seat the jambs and head against their intended backing and align their outer faces with the exterior door framing. - Integrate the head flashing and recheck the clear opening before drilling the selected hinge pattern. Check: The jambs are plumb, the head is level and the hinge backing is ready. ![Fit the door jambs and head. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-068/s55.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. Reference drawings: - [Door layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-layout/door-layout.svg?brand=1) ### 56. Build and hang the left door - Assemble the leaf flat with exterior stiles and rails; clamp square and fasten with the resolved door detail. - Support the leaf on blocks while fastening the selected hinges into the specified backing. - Set 1/8-inch side gaps, 1/8-inch top gap and 1/4-inch bottom gap; leave 3/8 inch between leaves. - Check hinge travel and sag before removing the supports. Check: The leaf holds its clearances and operates on the selected hardware without rubbing. ![Build and hang the left door. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-070/s56.gif?brand=1) Movement study for Build and hang the left door. Reference drawings: - [Door layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-layout/door-layout.svg?brand=1) ### 57. Build and hang the right door - Assemble the leaf flat with exterior stiles and rails; clamp square and fasten with the resolved door detail. - Support the leaf on blocks while fastening the selected hinges into the specified backing. - Set 1/8-inch side gaps, 1/8-inch top gap and 1/4-inch bottom gap; leave 3/8 inch between leaves. - Check hinge travel and sag before removing the supports. Check: The leaf holds its clearances and operates on the selected hardware without rubbing. ![Build and hang the right door. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-072/s57.gif?brand=1) Movement study for Build and hang the right door. Reference drawings: - [Door layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-layout/door-layout.svg?brand=1) ### 58. Fit the door meeting strip - 1 door meeting astragal over exterior frames: 1x2, 71 5/8 in long, actual section 3/4 x 1 1/2 in. - Close and align both leaves, then attach the strip to the designated active leaf only. - Keep the leaf-opening order, latch and selected weather seals clear through their full travel. Check: The strip covers the meeting gap without binding the opposite leaf. ![Fit the door meeting strip. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-073/s58.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. Reference drawings: - [Door layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-layout/door-layout.svg?brand=1) ### 59. Fit the pull and latch - Fit the selected pull, latch and fixed-leaf restraints into the specified solid backing. - Follow the hardware manufacturer's fastener and edge-distance instructions. Confirm the hinge, handle and latch quantities before ordering. - Operate the doors and hardware open and closed, and correct sag or binding. Check: Both leaves close, secure and reopen freely. ![Fit the pull and latch. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-074/s59.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. Reference drawings: - [Door layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-layout/door-layout.svg?brand=1) ### 60. Fit the corner trim - 2 corner front or rear trim: 1x4, 84 in long, actual section 3/4 x 3 1/2 in. - 2 corner front or rear trim: 1x4, 84 in long, actual section 3/4 x 3 1/2 in. - 2 corner side trim: 1x4, 84 in long, actual section 3/4 x 3 1/2 in. - 2 corner side trim: 1x4, 84 in long, actual section 3/4 x 3 1/2 in. - Fit each front or rear board over the edge of its side return, seating both boards against the measured T1-11 faces. - Preserve required bottom clearances and drainage paths; seal cut ends and fasten into the specified backing. Check: Every corner return closes without a gap and preserves the selected weather detail. ![Fit the corner trim. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-075/s60.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Corner trim](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-corner-trim/corner-trim.svg?brand=1) Corner trim ### 61. Cover the wall-to-gable seams - 1 gable-to-wall seam trim: 1x4, 91 3/4 in long, actual section 3/4 x 3 1/2 in. - 1 gable-to-wall seam trim: 1x4, 91 3/4 in long, actual section 3/4 x 3 1/2 in. - Center the continuous seam boards over the Z = 84-inch panel joint, fitting their ends between the corner trims. - Preserve the flashing and drainage detail behind the boards; fasten into the specified backing and finish cut ends. Check: Both horizontal seams are covered without replacing their flashing. ![Cover the wall-to-gable seams. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-076/s61.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Seam trim](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-seam-trim/seam-trim.svg?brand=1) Seam trim ### 62. Seal and finish the exterior - Allow wood and panels to dry to the coating manufacturer’s limits. - Seal only required joints; keep drainage and ventilation openings clear. - Prime exposed cuts, apply the selected finish and recheck door operation after coating. Check: The exterior has its required finish and all intended drainage paths remain open. Reference drawings: - [Front elevation](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-elevation/front-elevation.svg?brand=1) - [Side elevation](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-side-elevation/side-elevation.svg?brand=1) ### 63. Inspect before use - Compare foundation-to-roof connections, panel fastening and permanent bracing with the completed construction details. - Check wall plumb, roof alignment, flashing, trim support and both doors. - Remove temporary bracing only where the permanent structure replaces it. - Complete required inspections and loft access, edge protection and permitted-load documentation before use. Check: Required construction decisions and inspections are complete before occupancy or storage. Reference drawings: - [Front elevation](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-elevation/front-elevation.svg?brand=1) - [Side elevation](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-side-elevation/side-elevation.svg?brand=1) - [Loft bearing](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-bearing/loft-bearing.svg?brand=1) ## Drawings and views ![Completed 8 × 8 gambrel shed](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-001/overview.png?brand=1) Finished shed overview. ![Confirm the construction details. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-002/s01.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Lay out the footprint. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-003/s02.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Prepare the foundation. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-004/s03.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Set the foundation runners. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-005/s04.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Set the foundation runners. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-006/s04.gif?brand=1) Movement study for Set the foundation runners. ![Cut and mark the floor stock. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-007/s05.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Assemble the floor perimeter. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-008/s06.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Install the floor joists. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-009/s07.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Install the loft bearing blocks. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-010/s08.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Square and anchor the floor. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-011/s09.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Plan the T&G floor panels. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-012/s10.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Lay floor strip 1. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-013/s11.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Lay floor strip 2. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-014/s12.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Cut and mark the left wall. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-015/s13.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Assemble and raise the left wall. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-016/s14.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the left wall. ![Assemble and raise the left wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-017/s14.gif?brand=1) Movement study for Assemble and raise the left wall. ![Cut and mark the right wall. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-018/s15.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Assemble and raise the right wall. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-019/s16.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the right wall. ![Assemble and raise the right wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-020/s16.gif?brand=1) Movement study for Assemble and raise the right wall. ![Cut and mark the rear wall. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-021/s17.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Assemble and raise the rear wall. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-022/s18.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the rear wall. ![Assemble and raise the rear wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-023/s18.gif?brand=1) Movement study for Assemble and raise the rear wall. ![Cut and mark the front wall. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-024/s19.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Assemble and raise the front wall. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-025/s20.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. ![Assemble and raise the front wall. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-026/s20.gif?brand=1) Movement study for Assemble and raise the front wall. ![Lap the wall cap plates. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-027/s21.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Cut and mark the loft framing. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-028/s22.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Seat the wall-supported loft beam. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-029/s23.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Seat the wall-supported loft beam. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-030/s23.gif?brand=1) Movement study for Seat the wall-supported loft beam. ![Attach the rear loft ledger. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-031/s24.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Install the loft joists. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-032/s25.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Cut the loft panels. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-033/s26.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Fasten the loft deck. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-034/s27.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from above; front at the bottom. ![Cut and label the roof profiles. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-035/s28.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Raise the front end roof frame. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-036/s29.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Raise the front end roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-037/s29.gif?brand=1) Movement study for Raise the front end roof frame. ![Raise the rear end roof frame. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-038/s30.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Raise the rear end roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-039/s30.gif?brand=1) Movement study for Raise the rear end roof frame. ![Raise the intermediate 1 roof frame. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-040/s31.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Raise the intermediate 1 roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-041/s31.gif?brand=1) Movement study for Raise the intermediate 1 roof frame. ![Raise the intermediate 2 roof frame. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-042/s32.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Raise the intermediate 2 roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-043/s32.gif?brand=1) Movement study for Raise the intermediate 2 roof frame. ![Raise the intermediate 3 roof frame. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-044/s33.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Raise the intermediate 3 roof frame. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-045/s33.gif?brand=1) Movement study for Raise the intermediate 3 roof frame. ![Cut the gable infill and spacers. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-046/s34.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Fit the perpendicular gable infill. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-047/s35.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Fit the relieved end-frame spacers. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-048/s36.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Fit the inner end rafters. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-049/s37.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Fit the inner end rafters. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-050/s37.gif?brand=1) Movement study for Fit the inner end rafters. ![Lay out the T1-11 siding cuts. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-051/s38.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Prepare the wall weather details. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-052/s39.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Fasten the left wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-053/s40.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the left wall. ![Fasten the right wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-054/s41.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the right wall. ![Fasten the rear wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-055/s42.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the rear wall. ![Fasten the front wall siding. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-056/s43.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. ![Fit the gable siding panels. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-057/s44.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Cut and mark the roof panels. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-058/s45.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Fasten the roof sheathing. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-059/s46.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Fit the eave drip edges. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-060/s47.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Lay the roof underlayment. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-061/s48.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Fit the rake drip edges. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-062/s49.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Shingle the lower roof facets. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-063/s50.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Flash the gambrel knees. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-064/s51.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Shingle the upper roof facets. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-065/s52.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Finish the ridge. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-066/s53.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Cut and lay out the door leaves. Stock dimensions and layout references.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-067/s54.png?brand=1) Loose stock and measured datums. Mark these cuts before assembly. ![Fit the door jambs and head. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-068/s55.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. ![Build and hang the left door. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-069/s56.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Build and hang the left door. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-070/s56.gif?brand=1) Movement study for Build and hang the left door. ![Build and hang the right door. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-071/s57.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Build and hang the right door. Current components orange; earlier work gray. Movement.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-072/s57.gif?brand=1) Movement study for Build and hang the right door. ![Fit the door meeting strip. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-073/s58.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. ![Fit the pull and latch. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-074/s59.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from outside the front wall. ![Fit the corner trim. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-075/s60.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Cover the wall-to-gable seams. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-076/s61.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Seal and finish the exterior. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-077/s62.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Inspect before use. Current components orange; earlier work gray.](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/image-078/s63.png?brand=1) Orange: parts added now. Gray: previously installed parts. View from the front-right corner. ![Corner trim](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-corner-trim/corner-trim.svg?brand=1) Corner trim ![Door cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-cut-layout-02/door-cut-layout-02.svg?brand=1) Door cut layout 02 ![Door cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-door-cut-layout/door-cut-layout.svg?brand=1) Door cut layout ![Floor cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-cut-layout/floor-cut-layout.svg?brand=1) Floor cut layout ![Floor sheet layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-floor-sheet-layout/floor-sheet-layout.svg?brand=1) Floor sheet layout ![Footprint skids](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-footprint-skids/footprint-skids.svg?brand=1) Footprint skids ![Front wall cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-wall-cut-layout-02/front-wall-cut-layout-02.svg?brand=1) Front wall cut layout 02 ![Front wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-front-wall-cut-layout/front-wall-cut-layout.svg?brand=1) Front wall cut layout ![Gable cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-02/gable-cut-layout-02.svg?brand=1) Gable cut layout 02 ![Gable cut layout 03](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-03/gable-cut-layout-03.svg?brand=1) Gable cut layout 03 ![Gable cut layout 04](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-04/gable-cut-layout-04.svg?brand=1) Gable cut layout 04 ![Gable cut layout 05](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout-05/gable-cut-layout-05.svg?brand=1) Gable cut layout 05 ![Gable cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-gable-cut-layout/gable-cut-layout.svg?brand=1) Gable cut layout ![Left wall cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-left-wall-cut-layout-02/left-wall-cut-layout-02.svg?brand=1) Left wall cut layout 02 ![Left wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-left-wall-cut-layout/left-wall-cut-layout.svg?brand=1) Left wall cut layout ![Loft cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-cut-layout/loft-cut-layout.svg?brand=1) Loft cut layout ![Loft deck layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-loft-deck-layout/loft-deck-layout.svg?brand=1) Loft deck layout ![Rafter cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-rafter-cut-layout/rafter-cut-layout.svg?brand=1) Rafter cut layout ![Rear wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-rear-wall-cut-layout/rear-wall-cut-layout.svg?brand=1) Rear wall cut layout ![Right wall cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-right-wall-cut-layout-02/right-wall-cut-layout-02.svg?brand=1) Right wall cut layout 02 ![Right wall cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-right-wall-cut-layout/right-wall-cut-layout.svg?brand=1) Right wall cut layout ![Roof sheet layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-sheet-layout-02/roof-sheet-layout-02.svg?brand=1) Roof sheet layout 02 ![Roof sheet layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-roof-sheet-layout/roof-sheet-layout.svg?brand=1) Roof sheet layout ![Seam trim](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-seam-trim/seam-trim.svg?brand=1) Seam trim ![Siding cut layout 02](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-siding-cut-layout-02/siding-cut-layout-02.svg?brand=1) Siding cut layout 02 ![Siding cut layout](https://diyplans.org/media/packages/03bd94329b28d1ef43ee04771004c09163f3320397d584d2e05bcb6f3ed0b503/drawing-siding-cut-layout/siding-cut-layout.svg?brand=1) Siding cut layout ## Downloads [Get the plan package for $19 USD](https://diyplans.org/buy/gambrel-shed). Includes available shopping lists, cut lists and downloads for every configuration of this plan. ## Using the CAD files - Open the native FreeCAD file to inspect labeled individual solids and stock properties. STEP contains the same installed geometry for other CAD applications. - CAD dimensions are millimeters; schedules and drawings explicitly use inches. Use the labeled cut-profile coordinates, not printed image scale. - Match this variant and revision across every file. Keep all files for this shed size together.